Plastics — Phenolic mouldings — Determination of acetone-soluble matter

Plastics — Determination of apparent density of material that can be poured from a specified funnel

Plastics — Determination of apparent density of material that can be poured from a specified funnel

Plastics — Determination of apparent density of moulding material that cannot be poured from a specified funnel

Plastics — Determination of apparent density of moulding material that cannot be poured from a specified funnel

Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite

Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite

Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite

Plastics — Determination of temperature of deflection under load — Part 3: High-strength thermosetting laminates and long-fibre-reinforced plastics

Plastics — Determination of temperature of deflection under load — Part 3: High-strength thermosetting laminates and long-fibre-reinforced plastics

Plastics — Determination of temperature of deflection under load — Part 3: High-strength thermosetting laminates and long-fibre-reinforced plastics

Plastics — Phenol-formaldehyde mouldings — Determination of free phenols — Iodometric method

Plastics — Phenol-formaldehyde mouldings — Determination of free ammonia and ammonium compounds — Colorimetric comparison method

Plastics — Phenol-formaldehyde mouldings — Detection of free ammonia

Plastics — Compression moulding test specimens of thermosetting materials

Plastics — Compression moulding of test specimens of thermosetting materials

Plastics — Compression moulding of test specimens of thermosetting materials

Plastics — Phenolic moulding materials — Determination of acetone-soluble matter (apparent resin content of material in the unmoulded state)

Plastics — Phenolic moulding materials — Determination of acetone-soluble matter (apparent resin content of material in the unmoulded state)

Plastics — Unsaturated polyester resins — Determination of reactivity at 80 degrees C (conventional method)

Plastics — Phenolic moulding materials — Specification

Plastics — Phenolic moulding materials — Specification

Plastics — Determination of the viscosity of polymers in dilute solution using capillary viscometers — Part 5: Thermoplastic polyester (TP) homopolymers and copolymers

Plastics — Aminoplastic moulding materials — Specification

Plastics — Aminoplastic moulding materials — Specification

Plastics — Unsaturated polyester resins — Determination of acid value

Plastics — Unsaturated polyester resins — Determination of partial acid value and total acid value

Plastics (polyester resins) and paints and varnishes (binders) — Determination of partial acid value and total acid value

Ebonite — Determination of tensile strength and elongation at break

Ebonite — Determination of cross-breaking strength

Plastics — Unsaturated polyester resins — Measurement of gel time at 25 degrees C

Plastics — Unsaturated polyester resins — Measurement of gel time at 25 degrees C

Plastics — Unsaturated-polyester resins — Measurement of gel time at ambient temperature

Plastics — Unsaturated polyester resins — Determination of hydroxyl value

Plastics — Unsaturated polyester resins — Determination of hydroxyl value

Plastics — Thermosetting moulding materials — Determination of shrinkage

Plastics — Thermosetting moulding materials — Determination of shrinkage

Ebonite — Determination of hardness by means of a durometer

Plastics — Epoxide compounds — Determination of epoxide equivalent

Plastics — Epoxy compounds — Determination of epoxy equivalent

Plastics — Epoxy compounds — Determination of epoxy equivalent

Plastics — Polyester and epoxy casting resins — Determination of total volume shrinkage

Plastics — Unsaturated polyester and epoxy resins — Determination of overall volume shrinkage

Plastics — Unsaturated polyester and epoxy resins — Determination of overall volume shrinkage — Technical Corrigendum 1

Plastics — Aminoplastic moulding materials — Determination of volatile matter

Plastics — Aminoplastic moulding materials — Determination of volatile matter

Plastics — Unsaturated polyester resins — Part 1: Designation

Plastics — Unsaturated-polyester resins (UP-R) — Part 1: Designation system

Plastics — Unsaturated-polyester resins (UP-R) — Part 2: Preparation of test specimens and determination of properties

Plastics — Epoxide resins — Part 1: Designation

Plastics — Epoxy resins — Part 1: Designation

Plastics — Epoxy resins — Part 2: Preparation of test specimens and determination of properties

Plastics — Epoxy resins — Part 2: Preparation of test specimens and determination of properties

Plastics — Epoxy resins — Part 2: Preparation of test specimens and determination of properties of crosslinked epoxy resins

Thermosetting resin and UV curable resin — Determination of shrinkage by continuous measurement method

Plastics — Epoxide resins and glycidyl esters - Determination of inorganic chlorine (Under revision ISO 11376)

Plastics — Epoxy resins and related materials — Determination of easily saponifiable chlorine

Plastics — Epoxy resins and related materials — Determination of easily saponifiable chlorine

Plastics — Hardeners and accelerators for epoxide resins — Part 1: Designation

Plastics — Hardeners and accelerators for epoxy resins — Part 1: Designation

Plastics — Melamine-formaldehyde mouldings — Determination of extractable formaldehyde

Plastics — Unsaturated polyesters and epoxide resins — Determination of total chlorine content

Plastics — Polyols for use in the production of polyurethanes — Determination of degree of unsaturation by using iodine method

Plastics — Liquid epoxide resins — Determination of tendency to crystallize

Plastics — Liquid epoxy resins — Determination of tendency to crystallize

Plastics — Liquid epoxy resins — Determination of tendency to crystallize

Plastics — Melamine/phenolic moulding materials — Specification

Plastics — Melamine/phenolic moulding materials — Specification

Plastics — Hardeners and accelerators for epoxide resins — Determination of free acid in acid anhydride

Plastics — Thermosetting moulding materials — Determination of transfer flow

Plastics — Phenolic resins — Basis for classification

Plastics — Liquid phenolic resins — Conventional determination of non-volatile matter

Plastics — Liquid phenolic resins — Conventional determination of non-volatile matter

Plastics — Phenolic resin powder — Determination of flow distance on a heated glass plate

Plastics — Phenolic resin powder — Determination of flow distance on a heated glass plate

Plastics — Phenolic resin powder — Determination of flow distance on a heated glass plate

Plastics — Phenolic resin powder — Sieve analysis using air-jet sieve apparatus

Plastics — Phenolic resins — Determination of residual phenol content by gas chromatography

Plastics — Phenolic resins — Determination of residual phenol content by gas chromatography

Plastics — Phenolic resins — Determination of residual phenol content by gas chromatography

Plastics — Phenolic resins — Determination of pH

Plastics — Phenolic resins — Determination of reactivity on a B-transformation test plate

Plastics — Phenolic resins — Determination of reactivity on a B-transformation test plate

Plastics — Phenolic resins — Determination of reactivity on a B-transformation test plate

Plastics — Phenolic resins — Determination of hexamethylenetetramine content

Plastics — Phenolic resins — Determination of hexamethylenetetramine content — Kjeldahl method and perchloric acid method

Plastics — Phenolic resins — Determination of hexamethylenetetramine content — Kjeldahl method, perchloric acid method and hydrochloric acid method

Plastics — Liquid phenolic resins — Determination of water miscibility

Plastics — Liquid phenolic resins — Determination of water miscibility

Plastics — Basic materials for polyurethanes — Pure isocyanates — Analysis of isocyanate groups

Plastics — Phenolic resins in the liquid state or in solution — Determination of viscosity

Plastics — Basic materials for polyurethanes — Determination of the amounts of 2,4- and 2,6-isomers in toluenediisocyanate by infrared spectroscopy

Plastics — Phenolic resins — Determination of the gel time at a given temperature using automatic apparatus

Plastics — Phenolic resins — Determination of the gel time of resols under specific conditions using automatic apparatus

Plastics — Phenolic resins — Determination of free formaldehyde content

Plastics — Phenolic resins — Determination of free-formaldehyde content — Hydroxylamine hydrochloride method

Plastics — Amine epoxide hardeners — Determination of primary, secondary and tertiary amine group nitrogen content

Plastics — Phenolic resins — Determination of reactivity of resols under acid conditions

Plastics — Phenolic resins — Determination of the pseudo-adiabatic temperature rise of liquid resols when cured under acid conditions

Plastics — Phenolic resins — Determination of electrical conductivity of resin extracts

Plastics — Phenolic resins — Determination of electrical conductivity of resin extracts — Technical Corrigendum 1

Plastics — Phenolic resins — Definitions and test methods

Plastics — Phenolic resins — Classification and test methods

Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 1: General principles and moulding of multipurpose test specimens

Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 2: Small plates

Plastics — Thermosetting moulding materials — Injection moulding of multipurpose test specimens

Plastics — Thermosetting moulding materials — Evaluation of short-term performance at elevated temperatures

Plastics — Epoxy resins and glycidyl esters — Determination of inorganic chlorine

Plastics — Phenolic resins — Separation by liquid chromatography

Plastics — Condensation resins — Determination of free formaldehyde

Phenolic, amino and condensation resins — Determination of free-formaldehyde content

Plastics — Phenolic resins — Determination of heats and temperatures of reaction by differential scanning calorimetry

Plastics — Epoxy resins and related materials — Determination of total saponifiable chlorine

Plastics — Epoxy resins — Determination of degree of crosslinking of crosslinked epoxy resins by differential scanning calorimetry

Plastics — Epoxy resins — Determination of degree of crosslinking of crosslinked epoxy resins by differential scanning calorimetry (DSC)

Plastics — Phenolic powder moulding compounds (PF-PMCs) — Part 1: Designation system and basis for specifications

Plastics — Phenolic powder moulding compounds (PF-PMCs) — Part 2: Preparation of test specimens and determination of properties

Plastics — Phenolic powder moulding compounds (PF-PMCs) — Part 3: Requirements for selected moulding compounds

Plastics — Urea-formaldehyde and urea/melamine-formaldehyde powder moulding compounds (UF- and UF/MF-PMCs) — Part 1: Designation system and basis for specifications

Plastics — Urea-formaldehyde and urea/melamine-formaldehyde powder moulding compounds (UF- and UF/MF-PMCs) — Part 2: Preparation of test specimens and determination of properties

Plastics — Urea-formaldehyde and urea/melamine-formaldehyde powder moulding compounds (UF- and UF/MF-PMCs) — Part 3: Requirements for selected moulding compounds

Plastics — Melamine-formaldehyde powder moulding compounds (MF-PMCs) — Part 1: Designation system and basis for specifications

Plastics — Melamine-formaldehyde powder moulding compounds (MF-PMCs) — Part 2: Preparation of test specimens and determination of properties

Plastics — Melamine-formaldehyde powder moulding compounds (MF-PMCs) — Part 3: Requirements for selected moulding compounds

Plastics — Melamine/phenolic powder moulding compounds (MP-PMCs) — Part 1: Designation system and basis for specifications

Plastics — Melamine/phenolic powder moulding compounds (MP-PMCs) — Part 2: Preparation of test specimens and determination of properties

Plastics — Melamine/phenolic powder moulding compounds (MP-PMCs) — Part 3: Requirements for selected moulding compounds

Plastics — Unsaturated-polyester powder moulding compounds (UP-PMCs) — Part 1: Designation system and basis for specifications

Plastics — Unsaturated-polyester powder moulding compounds (UP-PMCs) — Part 2: Preparation of test specimens and determination of properties

Plastics — Unsaturated-polyester powder moulding compounds (UP-PMCs) — Part 3: Requirements for selected moulding compounds

Plastics — Unsaturated-polyester resins — Determination of reactivity at 130 degrees C

Plastics — Phenol-formaldehyde mouldings — Determination of free ammonia and ammonium compounds — Indophenol method

Plastics — Polyurethane raw materials — Determination of isocyanate content

Plastics — Polyurethane raw materials — Determination of isocyanate content — Technical Corrigendum 1

Plastics — Polyurethane raw materials — Determination of isocyanate content

Plastics — Polyurethane raw materials — Determination of isocyanate content — Amendment 1: Acceptable variations in the procedure for method B

Plastics — Polyurethane raw materials — Determination of isocyanate content

Plastics — Polyols for use in the production of polyurethane — Determination of water content

Plastics — Polyols for use in the production of polyurethane — Determination of water content

Plastics — Polyols for use in the production of polyurethanes — Determination of water content

Plastics — Aromatic isocyanates for use in the production of polyurethane — Determination of acidity

Plastics — Aromatic isocyanates for use in the production of polyurethane — Determination of acidity — Amendment 1

Plastics — Polyols for use in the production of polyurethane — Determination of basicity

Plastics — Polyols for use in the production of polyurethanes — Determination of basicity

Plastics — Polyols for use in the production of polyurethane — Determination of hydroxyl number

Plastics — Polyols for use in the production of polyurethane — Determination of hydroxyl number — Technical Corrigendum 1

Plastics — Polyols for use in the production of polyurethane — Determination of hydroxyl number

Plastics — Polyols for use in the production of polyurethanes — Determination of hydroxyl number

Plastics — Aromatic isocyanates for use in the production of polyurethanes — Determination of hydrolysable chlorine

Plastics — Aromatic isocyanates for use in the production of polyurethanes — Determination of hydrolysable chlorine

Plastics — Polyols for use in the production of polyurethanes — Determination of hydroxyl number by NIR spectroscopy

Plastics — Polyols for use in the production of polyurethanes — Determination of hydroxyl number by NIR spectroscopy

Plastics — Aromatic isocyanates for use in the production of polyurethanes — Determination of the isomer ratio in toluenediisocyanate

Plastics — Aromatic isocyanates for use in the production of polyurethanes — Determination of the isomer ratio in toluenediisocyanate

Plastics — Aromatic isocyanates for use in the production of polyurethanes — Determination of the isomer ratio in toluenediisocyanate (TDI)

Plastics — Epoxy powder moulding compounds (EP-PMCs) — Part 1: Designation system and basis for specifications

Plastics — Epoxy powder moulding compounds (EP-PMCs) — Part 2: Preparation of test specimens and determination of properties

Plastics — Epoxy powder moulding compounds (EP-PMCs) — Part 3: Requirements for selected moulding compounds

Plastics — Polyols for use in the production of polyurethane — Determination of degree of unsaturation by microtitration

Plastics — Polyols for use in the production of polyurethanes — Determination of degree of unsaturation by microtitration

Plastics — Epoxy resins — Test methods

Plastics — Epoxy resins — Test methods

Plastics — Determination of tensile properties at high strain rates

Plastics — Epoxy resins — Determination of degree of crosslinking of crosslinked epoxy resins by Fourier Transform Infrared (FTIR) Spectroscopy

Plastics — Epoxy resins — Determination of 1,2-glycol content

Plastics — Epoxy resins — Determination of 1,2-glycol content

Plastics — Polymer polyols for use in the production of polyurethane — Determination of the residual acrylonitrile and styrene monomer content by gas chromatography

Plastics — Polymer polyols for use in the production of polyurethanes — Determination of the residual acrylonitrile and styrene monomer content by gas chromatography

Plastics — Epoxy resins — Determination of electrical conductivity of aqueous resin extracts

Plastics — Epoxy resins — Determination of chlorine content — Part 1: Inorganic chlorine

Plastics — Epoxy resins — Determination of chlorine content — Part 1: Inorganic chlorine

Plastics — Epoxy resins — Determination of chlorine content — Part 2: Easily saponifiable chlorine

Plastics — Epoxy resins — Determination of chlorine content — Part 2: Easily saponifiable chlorine

Plastics — Epoxy resins — Determination of chlorine content — Part 3: Total chlorine

Plastics — Epoxy resins — Determination of chlorine content — Part 3: Total chlorine

Plastics — Polyols for use in the production of polyurethanes — Determination of basicity (total amine value), expressed as percent nitrogen

Plastics — Polyols for use in the production of polyurethanes — Determination of basicity (total amine value), expressed as percent nitrogen

Plastics — Aromatic isocyanates for use in the production of polyurethanes — Determination of total chlorine

Plastics — Aromatic isocyanates for use in the production of polyurethanes — Determination of total chlorine

Plastics — Aromatic isocyanates for use in the production of polyurethanes — Determination of total chlorine